Recently Viewed

Digital RGB LED Weatherproof Strip 60 LED -1m-WHITE

Digital RGB LED Weatherproof Strip 60 LED -1m-WHITE
  Zoom
Digital RGB LED Weatherproof Strip 60 LED -1m-WHITEDigital RGB LED Weatherproof Strip 60 LED -1m-WHITEDigital RGB LED Weatherproof Strip 60 LED -1m-WHITE
Our Price:  £22.22(Inc. 20% VAT)(£18.52 Exc. VAT)Earn 22 Loyalty Points
+

SKU:  PPADA1138
Part Number:  1138
Brand:  World Semi

Stock / Availability

Available Now:  

6 in stock, immediate despatch
Need more than we have? : Supplier out of stock
  (1 Review)

You thought it couldn't get better than our world-famous 32-LED-per-meter Digital LED strip but we will prove you wrong! You wanted twice the LEDs? We got it (well, its 1.875 times as many but that's within a margin of error). You wanted thinner strips? Now only 12.5 mm wide, 10 mm if you remove the strip from the casing. You wanted less noticable strip colour - this strip has white-coloured flex PCB, which will be less visible against white-painted walls. This is the strip with white flex PCB, its identical to the black 60 LED/meter except it has a different colour mask on the flex strip

All your dreams answered, yet there are a few things to watch for.

  • First up, the higher density means much higher power usage over a certain distance - 18 Watts max (~3.5 Amps @ 5V) per meter instead of 9.6 Watts max (~2 Amps @ 5V). The max rating is assuming all the LEDs are on full white, usually the actual current for colourful design is about 1/3 to 1/2 the max current. A good power supply such as our 5V 10A supply is key!
  • Second, to get high density, the controller chip is inside the LED, which is kind of cool, but also means that the chip only uses a single pin for input and a single pin for output. The protocol used is very very timing-specific and can only be controlled by microcontrollers with highly repeatable 100nS timing precision. We have example code for using with the Arduino Uno/Mega microcontroller at 8MHz and 16MHz, but it will not work with the Raspberry Pi, Basic Stamp, NETduino, any other interpreted/virtual machine microprocessor or any processor slower than 8 MHz. For those processors, check our 32 LED/meter digital LED strip which has SPI-like input/output and works well with Pi, NETduino, and other processors.
  • Third, just because you have all those pixels doesn't mean you have the RAM for it - the entire strip must be buffered in memory, and we've found many Arduino UNO projects only have about 1500 bytes of RAM available after all the extras are included - enough for about 500 LED pixels. If you want to drive the entire strip and have some other libraries included, use a Mega.

These LED strips are even more fun and glowy. There are 60 RGB LEDs per meter, and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set the colour of each LED's red, green and blue component with 8-bit PWM precision (so 24-bit colour per pixel). The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 1 digital output pin are required to send data down. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for you

The strip is made of flexible PCB material, and comes with a weatherproof sheathing. You can cut this stuff pretty easily with wire cutters, there are cut-lines every 0.65"/1.7cm (1 LED each). Solder to the 0.1" copper pads and you're good to go. Of course, you can also connect strips together to make them longer, just watch how much current you need!  You must use a 5V DC power supply to power these strips, do not use higher than 6V or you can destroy the entire strip

They come in 4 meter reels with a 2 or 3-pin JST SM connector on each end and separated power/ground wires. These strips are sold by the meter! If you buy 4 meters at a time, you'll get full reels with two connectors. If you buy less than 4m, you'll get a single strip, but it will be a cut piece from a reel which may or may not have a connector on it.

To wire up these strips we suggest picking up some JST SM plug and receptacle cables. You'll want one of each, one wire is for ground the other is for signal. For the power wire, you will also probably want a 2.1mm DC jack to wire in so you can connect one of our wall adapters to power it.

Adafruit has anUberguide has everything you need to use NeoPixels in any shape and size. Including ready-to-go library & example code for the Arduino UNO/Duemilanove/Diecimila, Flora/Micro/Leonardo, Trinket/Gemma, Arduino Due & Arduino Mega/ADK (all versions)


 


Customers who bought this item also bought:


Customer Reviews
Average Rating (1 Review):  
Write a Review and share your opinions!

Rating:  
Awesomely versatile and very bright!
Thursday, 21 July 2016  |  Lee

I bought these to make a sunrise alarm clock. They're super controllable and very bright.

 

This review has not been appraised.

Free Technical Support
Fast Delivery Options
Customer Loyalty Scheme

Proto-PIC - UK Distributor of Sparkfun, Arduino, BBC Micro Bit, Adafruit Electronic ComponentsProto-PIC ; UK Distributor of Sparkfun, Arduino, Adafruit, BBC Micro Bit electrical components